Electric clock movements and motors

LANSHIRE IN THE WALL MOVEMENT
Special movement for replacing defective in the wall
electric clocks or building new ones. 4" front plate for
mounting directly to an electrical box. 3/8" threaded
portion and 7/8" overall length hand shaft. 110 volt, 60cy,
standard U.S. electricity.
812128..........................................................49.50

Lanshire in the wall clock movement
Order this item

LANSHIRE XL7 MOTOR
Fits most Lanshire electric movements. Plate size: 1-3/4"
x 2-1/2", 110V, 60C, 2W. This is the motor and
back-plate only. You must remove the old motor by
taking off the 4 nuts in the corners of your old movement.
All of the gears will be loose because the entire
back-plate will be new. Keep all of your gears in place,
then install your new motor. Please see our instructions
page by clicking the link below. 110 volt, 60cy, standard
U.S. electricity. 812164.....................................$29.95
Click here for installation instructions

Lanshire XL7 motor
Order XL7 motor

LANSHIRE EHP CLOCK MOVEMENT
One of the last Lanshire movements still being made.
13/16" hand shaft length. Rear set knob, hanging hole
molded into housing, 6' cord and plug. 110 volt, 60cy,
standard U.S. electricity. EHP2R12C $49.95

Order this item

LANSHIRE GEARS, COMPLETE SET
This is a complete plastic gears for Lanshire clock
movements using an XL7 motor and have plastic
gears. If your gears are metal and fiber these will
not fit and there are no replacements. The shafts
that the hands mount on are available in only one
length so these may not fit your movement but the
auxiliary wheels are universal.
LANKIT $15.95

Lanshire clock gear set
Order this item

Hands for Lanshire movements
These hands fir the EHP and In the wall
movements. Minute hand is 5-1/4" from mounting
hole to tip of hand. Good for 11" to 12" clock face
diameter.
CH100.....................................................$5.00 per pair

Hands for Lanshire clock movements
Order this item

Red sweep second hand for Lanshire clock movements
Fits in the wall and EHP movements.4-1/4" from
mounting hole to tip of hand.
A1438...................................................$3.00 each

second hand for Lanshire clock movements
Order this item

SYNCHRON ELECTRIC MOTOR
A43RA Synchron 1 RPM, same as Synchron I43RA
and is a direct replacement motor. 10 tooth pinion, 4
mounting ears 110 volt, 60cy,
standard U.S. electricity.
A43RA $39.99 2 pc for $75.00 ($37.50 each)

Synchron A43RA clock  motor
Order this item

MINI ELECTRIC CLOCK MOVEMENT
Quartz type mini movement. 2-1/4" square case. Use
any of our quartz hands up to 7" long, You can use
second hands as well. 6' cord with plug. 120v 60hz.
Available in 3 shaft lengths: 110 volt, 60cy, standard
U.S. electricity.
Order #       Max dial thickness       Price each
101110       3/16"                           $9.50
101230       1/2"                             $9.50
101190       3/4"                             $9.50
View hands that will fit this movement
Explanation of "dial thickness"

electric quartz clock movement

All of our electric movements and motors are 110 volt, 60cy, standard U.S. electricity.

Glo Dial clock movements and accessories
Large industrial clock parts for tower clocks, bill boards, churches and buildings
requiring large hands. Ideal for outdoor use and back-lit clocks.
Click here for more information

About Us

Norkro Clock Parts has been distributing quality Clock Parts since 1972. Norkro has the clock part you want at the best price.

Norkro.com 18060 SW SALIX RIDGE ST Beaverton OR 97006
503-352-5483
clockhand@comcast.net

Information

Contact Us